MCUmall EPROM BIOS Chip Burner Forum
MCUmall EPROM BIOS Chip Burner Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
 Password:
Save Password
Forgot your Password?

 All Forums
 MCUmall Forums
 True USB Willem Programmer (GQ-2X,3X,4X & GQ-4x4)
 Gq-4x4 SLOW		  New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

SanderAlec

United Kingdom
4 Posts
Posted - 05/16/2017 :  05:02:19  Show Profile  Reply with Quote
Hello , i own a gq4x4 , software to the latest 7.11 but its slow. Im mainly programming W25Q64FWSIG or W25Q64CV (8 meg flash) and its taking its time ( ~ 8 minutes per operation ) doesnt matter if i read or write.

Back in the days i had a gq-4x which was working like a charm.
Reply #1

anniel

2572 Posts
Posted - 05/16/2017 :  08:21:00  Show Profile  Reply with Quote
Bad USB cables often slow down transfer speed.
Go to Top of Page
Reply #2

SanderAlec

United Kingdom
4 Posts
Posted - 05/17/2017 :  07:31:35  Show Profile  Reply with Quote
On the same cable + same usb port im using ezp and elnec . both are working fine. only gq is slow ....

edit. just tested now the OLD gq4x and worked as expected (read / write fast)

the new one 4x4 its still slow.
Edited by - SanderAlec on 05/17/2017 07:33:19
Go to Top of Page
Reply #3

SanderAlec

United Kingdom
4 Posts
Posted - 05/17/2017 :  07:43:21  Show Profile  Reply with Quote
This is the output from gq4x4 for a w25q64fwsig (1.8 , im using adapter) - doesnt matter as im getting the same results on the 3.3v ones eg w25q64fvsig
ID check OK
Reading... Buffer
Elapsed time: 282.26 seconds.
Read completed.

Erasing...
Elapsed time: 34.43 seconds.
Erase completed.

Writing... Buffer
Elapsed time: 326.50 seconds.
Device write completed OK

if i snap the same chip onto the chineese clone (ezp) gets the job done in 1 minute.
Go to Top of Page
Reply #4

SanderAlec

United Kingdom
4 Posts
Posted - 05/19/2017 :  02:31:33  Show Profile  Reply with Quote
bump?
Go to Top of Page
Reply #5

anniel

2572 Posts
Posted - 05/23/2017 :  10:30:31  Show Profile  Reply with Quote
Did you find the problem?
Go to Top of Page
Reply #6

supervizeur

462 Posts
Posted - 05/29/2017 :  06:18:18  Show Profile  Reply with Quote
Curious here also.
Go to Top of Page
Reply #7

anniel

2572 Posts
Posted - 05/29/2017 :  09:56:34  Show Profile  Reply with Quote
We'll never know.
Go to Top of Page
Reply #8

supervizeur

462 Posts
Posted - 06/04/2017 :  09:11:25  Show Profile  Reply with Quote
Probably.
Go to Top of Page
Reply #9

GQ5XSupport

104 Posts
Posted - 07/21/2017 :  04:22:31  Show Profile  Reply with Quote
If you program 8M chip often, consider use GQ 5X. It reads in less than 2 seconds.
Go to Top of Page
Reply #10

anniel

2572 Posts
Posted - 07/27/2017 :  14:09:15  Show Profile  Reply with Quote
quote:
Originally posted by GQ5XSupport

If you program 8M chip often, consider use GQ 5X. It reads in less than 2 seconds.


What's the official time for a 8M chip on th GQ-4X?
Go to Top of Page
Reply #11

supervizeur

462 Posts
Posted - 08/03/2017 :  06:16:58  Show Profile  Reply with Quote
quote:
Originally posted by anniel

quote:
Originally posted by GQ5XSupport

If you program 8M chip often, consider use GQ 5X. It reads in less than 2 seconds.


What's the official time for a 8M chip on th GQ-4X?


+1 A complete speed table would be nice.
Go to Top of Page
Reply #12

anniel

2572 Posts
Posted - 09/15/2017 :  04:56:41  Show Profile  Reply with Quote
quote:
Originally posted by supervizeur

quote:
Originally posted by anniel

quote:
Originally posted by GQ5XSupport

If you program 8M chip often, consider use GQ 5X. It reads in less than 2 seconds.


What's the official time for a 8M chip on th GQ-4X?


+1 A complete speed table would be nice.


Yes.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
MCUmall EPROM BIOS Chip Burner Forum © Copyright 2003 - 2009 Mcumall Electronics Inc. Go To Top Of Page
Generated in 0.09 sec. Snitz Forums 2000