| Author |
 Topic  |
|
|
Bad_Ad84
210 Posts |
 Posted - 03/10/2009 : 05:08:31
|
Hi, ive programmed the MX29LV160CB with no problems (around 100 of them) but this BB will erase and blank test fine, but errors instantly on a write.
any suggestions? |
|
| Reply #1
ZLM
2945 Posts |
Posted - 03/10/2009 : 07:49:03
|
Did you try any others, same brand?
Just make sure the chip is good.
Check the Temp. Unprotect check box see if it makes different.
|
 |
|
| Reply #2
Bad_Ad84
210 Posts |
Posted - 03/10/2009 : 11:41:35
|
i dont have anymore BB's, but it came from a working device, for the time being ive swapped it for a compatible one.
ill keep hold of this one and wait till more come in (this are modem repair jobs), when i get another BB ill try it then and see what happens and report my results.
and temp unprotect was first thing i tried, with no luck. |
Edited by - Bad_Ad84 on 03/10/2009 11:42:23 |
|
|
| Reply #3
fox_el_negro
Mexico
19 Posts |
Posted - 04/14/2009 : 18:55:29
|
i have same problem macronix chip
mx29lv160bb
the program reads the chip but cant program im using the last update!!
and also have problems on this chip The TE28F160 is made by Intel.(the intel chips came on the pansat 3500, 2700 and the surf board modem 5100)
some boxes have macronix amd and a rare brand saimpo(not shure) |
c64 |
|
|
| Reply #4
Bad_Ad84
210 Posts |
Posted - 04/14/2009 : 20:54:00
|
| ive had no issues with those intels. |
|
|
| Reply #5
Bad_Ad84
210 Posts |
Posted - 04/15/2009 : 10:33:52
|
| make sure you have voltage set at 3v if using GQ-4X with 5v it fails |
Edited by - Bad_Ad84 on 04/15/2009 11:08:16 |
|
|
| Reply #6
fox_el_negro
Mexico
19 Posts |
Posted - 04/18/2009 : 22:16:14
|
i have GQ-X3 same problem no change!!!
the intel t28f160cb3 have same problem, im using the same confuguration shows in board, and nop cant do...
on some other chips like the 29lv800 im using another brand to readit and programit whit no problems..
butt the intel no change dont program, can read butt no wrigth on it!!! |
c64 |
|
|
| Reply #7
Bad_Ad84
210 Posts |
Posted - 04/19/2009 : 15:52:23
|
| are you using the 16bit adapter with the address wires? |
|
|
| Reply #8
fox_el_negro
Mexico
19 Posts |
Posted - 04/19/2009 : 21:44:35
|
| yes the same one i buy mine on ebay whit it included!! |
c64 |
|
|
| Reply #9
ZLM
2945 Posts |
Posted - 04/20/2009 : 12:53:27
|
| can you post a setup picture? so that I can take a close look your setup. |
|
|
| Reply #10
Bad_Ad84
210 Posts |
Posted - 05/11/2009 : 02:29:41
|
ok, i have another BB chip and still having the same issues.
would you like me to send you one? |
Edited by - Bad_Ad84 on 05/11/2009 02:30:51 |
|
|
| Reply #11
ZLM
2945 Posts |
Posted - 05/11/2009 : 08:11:02
|
| Yes. Please send me a testing chip to find out why. Write to support@mcumall.com |
|
|
| Reply #12
ZLM
2945 Posts |
Posted - 05/24/2009 : 10:22:56
|
Received two MX29LV160BB chips. Tested on both GQ-3X,GQ-4X, software Re.4.01.
Test report as bellow:
========================
The GQ-3X programmer
========================
1. ADP-003 TSOP48 8 bit adapter. Select MX29LV160BB from software. Set adapter on 5V, 29F jumper position. Three address wires are connected(A19,A20,A21)
-ID OK
-READ OK
-ERASE OK (With Temporary Unprotect Enabled, make sure the yellow VPP LED is on when erase),ERASE will fail without Temporary Unprotect Enabled.
-Write OK (With Temporary Unprotect Enabled, make sure the yellow VPP LED is on when write)
-Verify OK
2. ADP-042 TSOP48 16 bit adapter.
Added new device in devices.txt if you are using software Re 4.01 or before version:
Name="MX29LV160BB(16bit)",ID="XXXX",Class="SST39VF1601",Category="FLASH",MFG="Macronix",Speed="5",Adapter="TSOP48 16 BIT Mode",Message="Set the adapter jumpers to VCC 5V and 29FX00 position.";
Select MX29LV160BB(16bit) from software. Set adapter on 5V, 29F jumper position. Three address wires are connected(A19,A20,A21)
-No ID function
-READ OK
-ERASE OK
-Write OK
-Verify OK
=======================
The GQ-4X programemr
=======================
1. ADP-003 TSOP48 8 bit adapter.
-Vcc selected to 5V, 29F setting.
-Software selected MX29LV160BB
-ID OK
-READ OK
-ERASE OK (With Temporary Unprotect Enabled, make sure the yellow VPP LED is on when erase)
-Write OK
-Verify OK
2. ADP-042 TSOP48 16 bit adapter.
-Adapter Vcc selected to 5V, 29F setting.
-Software selected MX29LV160BB(16bit)
-ID OK
-READ OK
-ERASE OK
-Write OK
-Verify OK |
|
|
| Reply #13
Bad_Ad84
210 Posts |
Posted - 06/01/2009 : 03:58:58
|
ill try again when i get another, but definately didnt work here.
ill try the 16bit adapter next time. |
|
|
| Reply #14
Bad_Ad84
210 Posts |
Posted - 06/08/2009 : 13:52:38
|
| im still having issues with this chip in both adapters... |
|
|
| Reply #15
Bad_Ad84
210 Posts |
Posted - 06/08/2009 : 13:58:37
|
ahh, solved it.
to erase i need temp unprotect, but when writing you need to untick it else you will get an error. |
|
|
| Reply #16
fox_el_negro
Mexico
19 Posts |
Posted - 07/07/2009 : 21:06:54
|
| post a picture of the isue!! |
c64 |
|
|
| Reply #17
Bad_Ad84
210 Posts |
Posted - 07/08/2009 : 04:35:32
|
| what issue? post says resolved. |
|
|
| Reply #18
fox_el_negro
Mexico
19 Posts |
Posted - 07/08/2009 : 08:33:56
|
quote:
Originally posted by Bad_Ad84
ahh, solved it.
to erase i need temp unprotect, but when writing you need to untick it else you will get an error.
mi english is realy bad!! |
c64 |
|
|
| |
Topic |
|
MX29LV160BB
