| Author |
 Topic  |
|
|
ianlill
United Kingdom
19 Posts |
 Posted - 12/12/2018 : 11:58:48
|
| i keep getting this message no matter what i do have tried 2 ecu same problem device blank check failed at address 0x0000 10 read =0x05 can you help |
ian |
|
| Reply #1
anniel
2602 Posts |
Posted - 12/13/2018 : 04:30:41
|
quote:
Originally posted by ianlill
i keep getting this message no matter what i do have tried 2 ecu same problem device blank check failed at address 0x0000 10 read =0x05 can you help
Did you erase them? |
 |
|
| Reply #2
ianlill
United Kingdom
19 Posts |
Posted - 01/02/2019 : 11:50:29
|
| yes wont write |
ian |
|
|
| Reply #3
anniel
2602 Posts |
Posted - 01/02/2019 : 12:04:49
|
quote:
Originally posted by ianlill
yes wont write
If your devices doesn't pass the blank check they are not erased correctly or damaged. |
|
|
| Reply #4
ianlill
United Kingdom
19 Posts |
Posted - 01/02/2019 : 12:24:42
|
| its blanked but wont write |
ian |
|
|
| Reply #5
anniel
2602 Posts |
Posted - 01/02/2019 : 12:41:52
|
quote:
Originally posted by ianlill
its blanked but wont write
So now they pass the blank check but simply refuse to write? Do you get an error message? |
|
|
| Reply #6
ianlill
United Kingdom
19 Posts |
Posted - 01/02/2019 : 12:58:11
|
failed,address =0x000000,devise=oxFF,buffer=ox12
get the above |
ian |
|
|
| Reply #7
anniel
2602 Posts |
Posted - 01/02/2019 : 16:01:17
|
quote:
Originally posted by ianlill
failed,address =0x000000,devise=oxFF,buffer=ox12
get the above
Probably damaged. Did you use the same part number in the device list? |
|
|
| Reply #8
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 00:40:10
|
| yes |
ian |
|
|
| Reply #9
anniel
2602 Posts |
Posted - 01/03/2019 : 06:54:12
|
quote:
Originally posted by ianlill
yes
What is the part number? |
|
|
| Reply #10
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 07:03:34
|
| do you mean this number m95404 |
ian |
|
|
| Reply #11
anniel
2602 Posts |
Posted - 01/03/2019 : 07:14:24
|
quote:
Originally posted by ianlill
do you mean this number m95404
What programmer do you use? |
|
|
| Reply #12
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 08:24:12
|
| gq-4x4 |
ian |
|
|
| Reply #13
anniel
2602 Posts |
Posted - 01/03/2019 : 08:28:51
|
quote:
Originally posted by ianlill
gq-4x4
Ok and which part number did you use in the device list?
|
|
|
| Reply #14
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 08:35:18
|
| used M95040 it blanks,go to write then get the Failed,address =0x000000,devise=oxFF,buffer=ox12 |
ian |
|
|
| Reply #15
anniel
2602 Posts |
Posted - 01/03/2019 : 08:43:00
|
quote:
Originally posted by ianlill
used M95040 it blanks,go to write then get the Failed,address =0x000000,devise=oxFF,buffer=ox12
Is your device a M95404 like you said earlier or a M95040? |
|
|
| Reply #16
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 08:47:57
|
| Sorry its M95040 |
ian |
|
|
| Reply #17
anniel
2602 Posts |
Posted - 01/03/2019 : 08:51:21
|
quote:
Originally posted by ianlill
Sorry its M95040
Is it pulled off the board? |
|
|
| Reply #18
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 08:59:54
|
| no its on my ecu what is it telling me when i get Failed,address =0x000000,devise=oxFF,buffer=ox12 |
ian |
|
|
| Reply #19
anniel
2602 Posts |
Posted - 01/03/2019 : 09:03:22
|
quote:
Originally posted by ianlill
no its on my ecu what is it telling me when i get Failed,address =0x000000,devise=oxFF,buffer=ox12
Ok, pull the chip off the board and try again. |
|
|
| Reply #20
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 09:07:32
|
same problem
|
ian |
|
|
| Reply #21
anniel
2602 Posts |
Posted - 01/03/2019 : 09:10:15
|
quote:
Originally posted by ianlill
same problem
Is this a DIP or does it need an adapter? |
|
|
| Reply #22
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 09:14:50
|
| it is done via a clip that goes on the chip |
ian |
|
|
| Reply #23
anniel
2602 Posts |
Posted - 01/03/2019 : 09:17:59
|
quote:
Originally posted by ianlill
it is done via a clip that goes on the chip
Did you test for good continuity from chip to ZIF? |
|
|
| Reply #24
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 09:24:42
|
| how do you do that |
ian |
|
|
| Reply #25
anniel
2602 Posts |
Posted - 01/03/2019 : 09:30:10
|
quote:
Originally posted by ianlill
how do you do that
Multimeter. |
|
|
| Reply #26
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 09:57:23
|
DONE THAT NO 5 VOLTS ON CLIP
|
ian |
|
|
| Reply #27
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 09:59:58
|
| Failed,address =0x000000,devise=oxFF,buffer=ox12 WHAT IS THAT TELLING ME so i can understand |
ian |
|
|
| Reply #28
anniel
2602 Posts |
Posted - 01/03/2019 : 10:11:27
|
quote:
Originally posted by ianlill
DONE THAT NO 5 VOLTS ON CLIP
You are not looking for 5V. You need to do a continuity check. What make and model is your multimeter? |
|
|
| Reply #29
anniel
2602 Posts |
Posted - 01/03/2019 : 10:15:39
|
quote:
Originally posted by ianlill
Failed,address =0x000000,devise=oxFF,buffer=ox12 WHAT IS THAT TELLING ME so i can understand
It is telling you just that. Your write failed at address 0x000000, the device reads 0xFF and the buffer is 0x12. |
|
|
| Reply #30
ianlill
United Kingdom
19 Posts |
Posted - 01/03/2019 : 10:47:36
|
| all ok on continuity check |
ian |
|
|
| Reply #31
anniel
2602 Posts |
Posted - 01/03/2019 : 11:14:26
|
quote:
Originally posted by ianlill
all ok on continuity check
Do an Hardware I/O Diagnostics on your GQ-4X4 to rule it out. |
|
|
| |
Topic |
|
balnk
Forum Locked
