| T O P I C R E V I E W |
| sylverster16v |
Posted - 12/02/2008 : 14:53:57
hi,
i have the GQ-4x and TSOP 20mm Adapter Complete Set.
Which adapter should i use and what and where should
i write in the devices.txt?
Thanks
 |
| 13 L A T E S T R E P L I E S (Newest First) |
| sylverster16v |
Posted - 01/04/2009 : 07:01:57
now i have the correct line for everyone who wants to work with MX29LV008CTTC-70G
Name="MX29LV008CT",ID="C23E",Class="SST39LF/VF040",Category="FLASH",MFG="Macronix",CodeSize="1048576",DIP="100011110101",Adapter="TSOP40A-DIP32 adapter",VCC="3.6V",Message=" "Speed="0" ,Set the adapter to 5V jumper position and connect A19 from adapter to programmer.";
|
| sylverster16v |
Posted - 01/02/2009 : 03:45:18
yes that was the correct answer :) |
| ZLM |
Posted - 01/01/2009 : 22:13:59
Great! It needs A19 address line to be connected. |
| sylverster16v |
Posted - 01/01/2009 : 17:21:54
Now for everyone:
add this line:
Name="AM29LV008BT",ID="013E",Class="SST39LF/VF040",Category="FLASH",MFG="AMD",CodeSize="1048576",DIP="100011110101",Adapter="TSOP40A-DIP32",VCC="3.6V";
and you have to connect A19!(GQ-4X also)
now everything works
|
| sylverster16v |
Posted - 01/01/2009 : 15:38:55
i checked the pin contacting so often,that a dream nights from tsop pins |
| ZLM |
Posted - 12/31/2008 : 22:03:39
something wrong with contacting. It should get 013E for the correct ID. |
| sylverster16v |
Posted - 12/30/2008 : 17:50:59
the datasheet says, the ID has to be 013E ?
Image Insert:
59.9 KB |
| ZLM |
Posted - 12/12/2008 : 19:34:20
Try this:
Name="AM29LV008B",ID="0137",Class="29LV800B",Category="FLASH",MFG="AMD",Adapter="TSOP40A-DIP32",VCC="3.6V",Message="Set the adapter to 5V."; |
| sylverster16v |
Posted - 12/12/2008 : 15:40:48
i will get Am29LV008BT-70REC ,do you think it is compatible to MX29LV008CTTC-70G and which device should i select in the software? |
| ZLM |
Posted - 12/05/2008 : 02:08:41
Not sure if the chip is dead. Jog the adapter little bit after locked it. This will help on pin contacting between adapter and ZIF socket. |
| sylverster16v |
Posted - 12/04/2008 : 07:16:05
if there is no other way and the chip is dead, which compatible other chips can i buy for MX29LV008CTTC-70G ?? |
| ZLM |
Posted - 12/03/2008 : 11:50:47
Try to get the ID first before doing anything else.
Close the 3V6 jumper will be 5V.
Close all 3 jumpers will be fine.
Most likely is the contacting problem. Check your pin contacting with the adapter and adapter pin with the programmer.
Your chip is brand new or used?
Can you take a close look picture? |
| ZLM |
Posted - 12/02/2008 : 22:51:15
Adapter="TSOP40A"
Try this line:
Name="MX29LV008T",ID="C23E",Class="29LV800T",Category="FLASH",MFG="Macronix",Adapter="TSOP40A-DIP32 adapter",VCC="3.6V",Message="Set the adapter to 5V jumper position.";
|
